Transmission Mounts
SKU: TCP0319
BMW MANUAL TRANSMISSION MOUNTS - E30, E36, E46, E21, E28, E39, E90, E92
WHAT ARE POLY TRANS MOUNTS?
The 80A polyurethane transmission mounts are meant for that OEM + feel. That means you want a subtle upgrade for your street car without too much of a compromise in comfort, these bushings are a happy medium. These poly mounts are designed for the street enthusiast. The price is for a pair (2 units). This poly transmission mount kit comes with everything you need to do 1 car.
Also available in 95A for track use, these are harder mounts.
WHY REPLACE YOUR TRANSMISSION MOUNTS?
These poly transmission mounts will have less movement under braking and cornering and, moreover, will not transfer much noise into the cabin which will make the ride a bit easier. These are a bolt through design (10.9-grade hardware); Hardware has a nylon insert, to ensure it does not back out on its own. These mounts are great for spiritedly-driven BMW streetcars.
WILL THESE POLY MOUNTS FIT MY BMW CAR?
- E30
- E36
- E24
- E28
- E46
- E90
- E92
- E21
- E34
- E39
- Z3
- DOES NOT FIT E30 M3 model
WHAT ARE THE BENEFITS OF 80A POLY TRANS MOUNTS?
- Adds responsiveness
- Reduced noise (compared to Delrin)
- Longer life than rubber OEM mounts
- Streetcar approved
- Does not all engine movement under heavy braking or acceleration
- Lifetime Garagistic warranty
- Transmit more power
- Oil, water, and solvent resistant
Installation Instructions
TORQUE SPEC: 9-12 ft/lbs + Blue Locktite
NOTE: Poly bushings should be torqued until they start to see deformation then back the nut .5 to 1 rotation off. Polyurethane trans bushings that are too tight will transfer vibrations and increase overall harshness.
Step 1: Safely jack up the vehicle from the front or rear and lower it securely on jack stands. Gently rock the vehicle to make sure it has seated properly on the jack stands
Step 2: Support the transmission with the jack and remove the bottom nuts of the transmission mounts and the 4 trans bracket bolts. Lastly, remove the two nuts of the trans mounts
Step 3: Install the trans bracket with loose bolts so it can slide back and forward
Step 4: Slightly raise the transmission so that the mount can slide in place with the bolt and washer going on top of the ear of the transmission. Install the washer and nut on the bottom
Step 5: Slide the trans bracket and mount as far forward as possible and tighten the bracket bolts
Step 6: Lower the trans on the mount and tighten trans mount bolts. Torque to 9-12 ft lbs
Do not over tighten !
Customers also bought
E30 Shifter bushing setE30 POLYURETHANE ROUND SHIFTER BUSHING KIT
This is our complete E30 polyurethane shifter bushing rebuild kit.
Our Garagistic polyurethane rear carrier bushing replaces the original rubber bushing found inside 25111220707 (which…€ 72,50
E30 M20 Engine mountsBMW ENGINE MOUNTS - E30 M20WHAT ARE POLY TRANS MOUNTS?The 80A polyurethane engine mounts are meant for that OEM + feel. That means you want a subtle upgrade for your street car without too much of a compromise in comfort, these…
€ 65,00
E30 M20 Delrin Engine MountsE30 M20 Delrin Engine Mounts
These E30 Solid Delrin M20 motor are a step up above PU mounts. These are the ultimate in performance. These are solid bushings. These will hold the engine and transmission with near no movement under…€ 65,00
Rempedaal bus - DelrinDELRIN BRAKE PEDAL BUSHINGS (E30, E36, E46, Z3, Z4)Got a loose or noisy clutch pedal arm driving you crazy? Sloppy? Side to side play? Does pedal sit at an angle? Well, it's pretty common in aging BMW's! The original E30, E36, and…
€ 22,50
